Let the toilet fill up, then perform a test flush to make sure everything is working properly. Connect the Water SupplyĪttach the water supply line to the toilet tank and turn on the water. Use the hacksaw to shorten the bolts if they are sticking out above the nuts, then cap them.įinally, caulk the area where the tile meets the toilet bowl to make sure everything is securely in its place and to avoid ruining your bathroom floor in the case of a leak. Make sure you don’t overtighten, which can cause the base to crack.
You’re almost done! Now, you have to thread the nuts and washers on the toilet floor bolts - alternate tightening between each side until they’re both secure. Place some pennies underneath the stool to level it instead. Make sure the toilet is level, but don’t try to move it if it’s not! This will break the wax seal, and you’ll have to start all over. Once the toilet is in place, press down to set the seal.
#New wax ring for toilet diy install
Then, install the flange bolts, ensuring the threaded ends are pointing up.Ĭarefully and preferably with the help of a buddy, lower the new toilet over the flange so that the bolts enter the holes on the stool. Be careful about not damaging the wax ring and placing it down in the right spot because once installed, it cannot be reused.
Remove the old rag blocking the sewer line opening and place the new wax ring inside the flange. If you notice it’s worn down or broken, you’ll need to replace this part as well. Once the wax seal is completely removed, inspect the flange for damage. Dispose of the wax seal immediately, so it doesn’t stick to your bathroom floor. Use a putty knife to remove the wax seal. Grab an old rag, wrap it in plastic, and stuff it in the opening (but not too far down) to block the sewer gases. Therefore, when you remove the toilet and open up access to the sewer line, all the lovely smells will immediately start coming out. The wax seal is important in keeping the wastewater contained on its journey to the sewer pipes, and it’s also the key to keeping your bathroom smelling fresh and clean. Here’s the most disgusting part of the whole removal/installation process: removing the wax seal. You can also try separating the tank from the bowl. Warning: Toilets can be heavy, so be careful when you remove this. Then, gently tilt the bowl from side to side to detach it. If it is caulked, use a utility knife to break the connection.
Pull the Toiletīefore you pull the toilet, check to see if the base is caulked. If the nuts and bolts still don’t nudge, use the hacksaw to cut them at the base. Let the oil sit for a little bit before trying again. If these pieces are being stubborn and not moving, use the lubricant to loosen them. Use the adjustable wrench to loosen the nuts, washers, and bolts. This should be pretty easy to pop off, but you can also use a screwdriver if necessary. Remove the plastic caps (also known as toilet bolt caps) that cover the bolts. Place the water supply line in the bucket in case there’s any water inside that needs to drain out. Then, disconnect the toilet tank from the water supply line using the tongue-and-groove pliers. Use the sponge and bucket to remove any remaining water. However, you may find some water lingering around at the bottom. With the water supply connection severed, they will not refill. Once the water is off, flush the toilet to drain the tank and the bowl. Turn Off the Waterįirst things first, you have to turn off the water supply by turning the stop valve on the wall, so you don’t find yourself dealing with an accidental plumbing disaster. Also, just to be safe, try to find a new toilet that matches your current one as much as possible. Measure the distance from the toilet’s bolts to the wall to get an idea of the waste pipe size. Ugh! Avoid this hassle altogether by measuring your current toilet before you purchase a new one. Nothing is more frustrating than realizing your new toilet doesn’t fit halfway through your DIY installation. Follow this step-by-step guide to toilet replacement, and don’t hesitate to contact us if you need toilet plumbing service! Tools and Materials Replacing and installing a new toilet isn’t rocket science, but it does require patience, the right tools, and a bit of plumbing know-how.
0 kommentar(er)
